The design of a functionally graded porous structure (FGPS) for use in prosthetic devices is crucial for meeting both mechanical and biological requirements. One of the most commonly used cellular structures in FGPS is the triply periodic minimal surface (TPMS) structure due to its ability to be defined by implicit equations, which allows for smooth transitions between layers. This study evaluates the feasibility of using a novel β-Ti21S alloy to fabricate TPMS-based FGPS. This beta titanium alloy exhibits low elastic modulus (53 GPa) and good mechanical properties in as-built condition. Two TPMS FGPSs with relative density gradients of 0.17, 0.34, 0.50, 0.66, and 0.83 and unit cell sizes of 2.5 mm and 4 mm were designed and fabricated using laser powder bed fusion (LPBF). The as-manufactured structures were analyzed using scanning electron microscopy (SEM) and X-ray micro-computed tomography (μ-CT), and the results were compared to the design. The analysis revealed that the pore size and ligament thickness were undersized by less than 5%. Compression tests showed that the stabilized elastic modulus was 4.1 GPa for the TPMS with a 2.5 mm unit cell size and 10.7 GPa for the TPMS with a 4 mm unit cell size. A finite element simulation was performed to predict the specimen’s elastic properties, and a lumped model based on lattice homogenized properties was proposed and its limitations were explored.
Metrological characterization of porosity graded β-Ti21S triply periodic minimal surface cellular structure manufactured by laser powder bed fusion / Emanuelli, Lorena; De Biasi, Raffaele; Du Plessis, Anton; Lora, Carlo; Jam, Alireza; Benedetti, Matteo; Pellizzari, Massimo. - In: INTERNATIONAL JOURNAL OF BIOPRINTING. - ISSN 2424-8002. - STAMPA. - 9:4(2023). [10.18063/ijb.729]
Metrological characterization of porosity graded β-Ti21S triply periodic minimal surface cellular structure manufactured by laser powder bed fusion
Emanuelli, Lorena;De Biasi, Raffaele;Jam, Alireza;Benedetti, Matteo;Pellizzari, Massimo
2023-01-01
Abstract
The design of a functionally graded porous structure (FGPS) for use in prosthetic devices is crucial for meeting both mechanical and biological requirements. One of the most commonly used cellular structures in FGPS is the triply periodic minimal surface (TPMS) structure due to its ability to be defined by implicit equations, which allows for smooth transitions between layers. This study evaluates the feasibility of using a novel β-Ti21S alloy to fabricate TPMS-based FGPS. This beta titanium alloy exhibits low elastic modulus (53 GPa) and good mechanical properties in as-built condition. Two TPMS FGPSs with relative density gradients of 0.17, 0.34, 0.50, 0.66, and 0.83 and unit cell sizes of 2.5 mm and 4 mm were designed and fabricated using laser powder bed fusion (LPBF). The as-manufactured structures were analyzed using scanning electron microscopy (SEM) and X-ray micro-computed tomography (μ-CT), and the results were compared to the design. The analysis revealed that the pore size and ligament thickness were undersized by less than 5%. Compression tests showed that the stabilized elastic modulus was 4.1 GPa for the TPMS with a 2.5 mm unit cell size and 10.7 GPa for the TPMS with a 4 mm unit cell size. A finite element simulation was performed to predict the specimen’s elastic properties, and a lumped model based on lattice homogenized properties was proposed and its limitations were explored.File | Dimensione | Formato | |
---|---|---|---|
729-2540-1-PB.pdf
accesso aperto
Tipologia:
Versione editoriale (Publisher’s layout)
Licenza:
Creative commons
Dimensione
11.24 MB
Formato
Adobe PDF
|
11.24 MB | Adobe PDF | Visualizza/Apri |
729-2540-1-PB_compressed.pdf
accesso aperto
Tipologia:
Versione editoriale (Publisher’s layout)
Licenza:
Creative commons
Dimensione
3.35 MB
Formato
Adobe PDF
|
3.35 MB | Adobe PDF | Visualizza/Apri |
I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione