Time-lag is the most important parameter describing the conformance of a piezometer because it represents the time that it takes for the instrument to reach equilibrium when there is a pore water pressure change in the soil. The use of fully grouted piezometers would make the installation easier and faster than the conventional one, since it prevents the failure risks during the placement of the sand pack and the overlying bentonite seal. This paper describes a number of laboratory tests performed to evaluate the time-lag of fully grouted piezometers. A pore water pressure change was applied at the bottom of cylindrical samples of grout and the pressure equalization was measured at the top. The samples were made of a cement-bentonite mixture and were 2 cm, 4 cm or 8 cm in height. Time –lags resulted in no longer than 6 minutes, that is a time generally acceptable in geotechnical projects. It was also found that the time-lag relies on the pore water pressure value. For a given draining path length, the higher the pore water pressure the shorter the response time. This behaviour has been explained by assuming that the time-lag depends on both the hydraulic and compressible characteristics of the grout mixture and that these characteristics vary with the pore water pressure because the grout is in a quasi saturated state.

Laboratory tests for measuring the time-lag of fully grouted piezometers / Simeoni, Lucia. - In: JOURNAL OF HYDROLOGY. - ISSN 0022-1694. - 438-439:(2012), pp. 215-222. [10.1016/j.jhydrol.2012.03.025]

Laboratory tests for measuring the time-lag of fully grouted piezometers

Simeoni, Lucia
2012-01-01

Abstract

Time-lag is the most important parameter describing the conformance of a piezometer because it represents the time that it takes for the instrument to reach equilibrium when there is a pore water pressure change in the soil. The use of fully grouted piezometers would make the installation easier and faster than the conventional one, since it prevents the failure risks during the placement of the sand pack and the overlying bentonite seal. This paper describes a number of laboratory tests performed to evaluate the time-lag of fully grouted piezometers. A pore water pressure change was applied at the bottom of cylindrical samples of grout and the pressure equalization was measured at the top. The samples were made of a cement-bentonite mixture and were 2 cm, 4 cm or 8 cm in height. Time –lags resulted in no longer than 6 minutes, that is a time generally acceptable in geotechnical projects. It was also found that the time-lag relies on the pore water pressure value. For a given draining path length, the higher the pore water pressure the shorter the response time. This behaviour has been explained by assuming that the time-lag depends on both the hydraulic and compressible characteristics of the grout mixture and that these characteristics vary with the pore water pressure because the grout is in a quasi saturated state.
2012
Simeoni, Lucia
Laboratory tests for measuring the time-lag of fully grouted piezometers / Simeoni, Lucia. - In: JOURNAL OF HYDROLOGY. - ISSN 0022-1694. - 438-439:(2012), pp. 215-222. [10.1016/j.jhydrol.2012.03.025]
File in questo prodotto:
File Dimensione Formato  
GT12 S01 Simeoni.JHydr.pdf

Solo gestori archivio

Tipologia: Post-print referato (Refereed author’s manuscript)
Licenza: Tutti i diritti riservati (All rights reserved)
Dimensione 845.45 kB
Formato Adobe PDF
845.45 kB Adobe PDF   Visualizza/Apri

I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/11572/143211
Citazioni
  • ???jsp.display-item.citation.pmc??? ND
  • Scopus 8
  • ???jsp.display-item.citation.isi??? 7
  • OpenAlex ND
social impact