Anisotropic dimensional change on sintering may strongly affect the precision of parts produced by press and sinter. In previous work a design procedure accounting for anisotropic dimensional change of axi-symmetric parts (disks and rings) has been developed on the basis of experimental data. In this work the procedure has been applied to predict the anisotropic dimensional change of real parts produced in industrial conditions, providing that coaxial rings were identified in the geometry of the actual parts. Parts were highly different for material, complexity of geometry, green density and process conditions. Parts were measured in the green and sintered state and the measured dimensional changes were compared to the predicted ones, finding a good agreement. The procedure was also adapted to predict dimensional change of an oval feature, and highly satisfactory results were obtained.

Design for Powder Metallurgy: Predicting Anisotropic Dimensional Change on Sintering of Real Parts / Cristofolini, I.; Molinari, A.; Zago, M.; Amirabdollahian, S.; Coube, O.; Dougan, M. J.; Larsson, M.; Schneider, M.; Valler, P.; Voglhuber, J.; Wimbert, L.. - In: INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING. - ISSN 2234-7593. - STAMPA. - 2019, 20:4(2019), pp. 619-630. [10.1007/s12541-019-00030-2]

Design for Powder Metallurgy: Predicting Anisotropic Dimensional Change on Sintering of Real Parts

I. Cristofolini;A. Molinari;M. Zago;S. Amirabdollahian;
2019-01-01

Abstract

Anisotropic dimensional change on sintering may strongly affect the precision of parts produced by press and sinter. In previous work a design procedure accounting for anisotropic dimensional change of axi-symmetric parts (disks and rings) has been developed on the basis of experimental data. In this work the procedure has been applied to predict the anisotropic dimensional change of real parts produced in industrial conditions, providing that coaxial rings were identified in the geometry of the actual parts. Parts were highly different for material, complexity of geometry, green density and process conditions. Parts were measured in the green and sintered state and the measured dimensional changes were compared to the predicted ones, finding a good agreement. The procedure was also adapted to predict dimensional change of an oval feature, and highly satisfactory results were obtained.
2019
4
Cristofolini, I.; Molinari, A.; Zago, M.; Amirabdollahian, S.; Coube, O.; Dougan, M. J.; Larsson, M.; Schneider, M.; Valler, P.; Voglhuber, J.; Wimbert, L.
Design for Powder Metallurgy: Predicting Anisotropic Dimensional Change on Sintering of Real Parts / Cristofolini, I.; Molinari, A.; Zago, M.; Amirabdollahian, S.; Coube, O.; Dougan, M. J.; Larsson, M.; Schneider, M.; Valler, P.; Voglhuber, J.; Wimbert, L.. - In: INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING. - ISSN 2234-7593. - STAMPA. - 2019, 20:4(2019), pp. 619-630. [10.1007/s12541-019-00030-2]
File in questo prodotto:
File Dimensione Formato  
Cristofolini2019_Article_DesignForPowderMetallurgyPredi.pdf

Solo gestori archivio

Tipologia: Versione editoriale (Publisher’s layout)
Licenza: Tutti i diritti riservati (All rights reserved)
Dimensione 4.11 MB
Formato Adobe PDF
4.11 MB Adobe PDF   Visualizza/Apri
DfS_IJPEM_final.pdf

Open Access dal 01/05/2020

Tipologia: Post-print referato (Refereed author’s manuscript)
Licenza: Tutti i diritti riservati (All rights reserved)
Dimensione 3.64 MB
Formato Adobe PDF
3.64 MB Adobe PDF Visualizza/Apri

I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/11572/229976
Citazioni
  • ???jsp.display-item.citation.pmc??? ND
  • Scopus 12
  • ???jsp.display-item.citation.isi??? 6
social impact